Cordless driver or drill is always considered to be significant and important equipment for obvious reasons.
Having a decent cordless drill machine is always considered as an important investment.
Proper care has to be taken of this valuable asset.
Though high quality drills are known to last long, nevertheless, even the most durable driver can sometimes break down if not maintained properly.
Here are 10 Cordless drill tips for the smart DIYer in you:
1. Oil the Cordless Drill
Just like any other mechanical equipment, a cordless drill comes with various moving parts.
In order to keep the parts intact and working you need to apply oil on a regular basis.
More importantly you need to oil the chuck part. The chuck is known to be the main part which holds together all the bits.
2. Clean the Drill
Cordless drills do one hell of a job, penetrating through the hard surface.
Penetrating through drywall, wood, concrete is likely to leave the machine very dusty.
These dust particles from the drywall gypsum, fine wood particles, etc. can make their way to the motor parts of a cordless drill.
Eventually, the drill can get clogged with the dust and particles, thus causing the machine to overheat heavily and burnout.
This is why you need to properly clean the cordless drill to keep the machine in good condition.
Blowing particles and dust out of the vents of the drill can help its motor breathe.
In order to do this, you can use any blow tool that you may like.
3. Always keep the drill in dry place
The power of this drill is largely dependent on its various motor parts, gears and other small parts that collectively offer proper torque and speed.
To keep the drill in the best condition, you are really supposed to keep it in a dry place.
Humid surroundings can severely damage the tool creating rust on the chuck as well as motor parts of the tool.
4. Temperature requirements
A cordless drill can even be severely affected or damaged by temperature, specifically the battery.
The drill and its batteries are required to be kept at normal room temperature (22C/72F).
Freezing conditions are likely to freeze the motor, as well as compression of gears, thus burning out gears and motors.
On the other hand, the comparatively high temperature can reduce the life of its batteries. This is why, it is important to store this tool at normal room temperature.
5. Keep the tool off the ground
Keeping the cordless drill machine off the ground is very important to keep the machine intact and in the best condition possible.
Keeping the drill on the ground while working outside creates a possibility of dust and grass from the ground getting into the machine.
Wet dirt and grass can severely damage the tool.
That apart, wet blades of the grass are likely to spread water in motor vents, thus increasing the chances of a short circuit in a cordless drill.
On the other hand, it can even be a safety hazard if you put the tool on the ground after use, especially at places where there is a lot of foot traffic.
People are also likely to trip on this tool or can even damage it.
6. Use sharp drill bits
The power of a cordless drill is as good as its bit’s ability to penetrate the surface.
If you go for the dull bits, then it is highly possible that your work won’t be done properly.
Not only that, dull bits can cause comparatively longer work periods along with friction overload which will eventually result in undue stress on the motor.
This is why it is very important for you to use perfectly sharp bits before you start any project.
That apart, you are also required to utilize the correct bits suited for a specific surface.
For example, you are never recommended to utilize wood bits for a concrete surface.
7. Drill the bit safely
If you go for the dull bits, they can cause a variety of serious safety issues for obvious reasons.
In case the bit pieces are not properly sharp, they are highly likely to get jammed into the surface.
Thus, the resulting torque can cause the drill to spin, thus injuring your hands or wrists.
On the other hand, it can also be dangerous to use the cordless drill if there is someone below you or you are standing or working on a ladder; it is likely to make you lose your balance.
8. Buy drills within a specified RPM range
The speed of drill is basically measured in the rotations per minute or RPM.
While purchasing a drill, you are supposed to buy a drill with the RPM range of around 300 to 1,500 for carrying out a variety of the tasks.
9. Use high speed and slow speed accordingly
You should know that a higher speed is required to drill holes.
On the other hand, lower speed is used to drive screws.
Always try to use comparatively slower speed for greater torque in order to avoid stripping screws.
Remember, more the torque, better it is to drill into the harder surfaces.
10. Other Safety Tips
There are various other safety tips that you need to follow religiously before you start working with a cordless drill.
It is important for you to start each project with a completely charged cordless drill for your convenience.
This way you are less likely to run out of batteries. Some other useful cordless drill tips are given below:
# Some drill chargers can take quite a few hours to get the drill batteries fully recharged.
That is why you should look for the chargers that take less time to charge the batteries.
# Don’t forget to take required precautions as well as always wear the safety gear at the time of using drills.
Always put on proper glasses for to prevent debris from getting into your eyes and wear gloves to avoid getting blistered.
# It is also important to do extensive online research about proper methods of using the cordless drill as well as its safety measures.